Authentic JDM Parts

Quality OEM and aftermarket parts for your Japanese vehicles. From engines to body parts — we've got you covered.

← Browse by Make / Model instead
209+
Parts Available
100%
Quality Guaranteed
Fast
Shipping
Showing 12 of 209 parts
No image available
New
Brake Pads and Shoes
Honda Step-Wagon / Odyssey Front Brake Pads
New
Front brake pad set covering the RG-series Honda Step-Wagon and the RB-series Honda Odyssey. The companion front set to part 43022-SFE-N00. The fronts on both platforms do the bulk of the braking and wear accordingly, typically two to three times faster than the rears. Wear is usually even, and the first sign is the wear indicator squealing under light braking. Fit as an axle set and check disc thickness against the minimum stamped on the disc hub while the caliper is off. A pedal pulsation on these is almost always disc runout rather than a pad problem, and fitting new pads to a warped disc will not fix it. Fits Step-Wagon RG1 to RG4 and Odyssey RB1 to RB4.
No image available
New
Brake Components
Daihatsu Hijet / Atrai Front Brake Rotors
New
Front brake rotors for the Daihatsu Hijet and Atrai, covering the S200 and S210 series kei platforms. Kei truck and van front discs are small and light, which means they heat quickly and are unusually sensitive to being run past their minimum thickness. On a vehicle this size a disc that has been skimmed once or has worn a deep outer lip should simply be replaced, there is very little material to work with in the first place. Replace rotors in axle pairs so braking stays balanced side to side, and fit new pads at the same time. Clean the hub face back to bare metal before mounting: rust or debris trapped between hub and rotor is the most common cause of runout and the brake judder that follows it. Available in Hapad and Pitwork depending on stock, please ask which is currently on the shelf if you have a preference.
No image available
New Only 3 left
Brake Pads and Shoes
Honda Fit / Jazz Front Brake Pads
New
Front brake pad set carrying Hitachi part number AN411WK, a widely applied Honda front pad covering a broad span of the Civic, Fit / Jazz, City, Integra, CR-X, Prelude and Stream range. Hitachi is a Japanese OE-tier supplier, and this is a conventional sliding-caliper front pad with the usual mechanical wear indicator. Fit as an axle set, clean the carrier abutments, and make sure the shims are present and correctly seated, missing shims are the usual cause of squeal after a pad change on small Hondas. Because this pad number spans a wide range of models and years, please confirm fitment against your chassis code and model year before ordering. Disc diameter varies across the vehicles listed and not every variant within a model line takes this pad.
No image available
New Only 2 left
Brake Pads and Shoes
Toyota Century Rear Brake Pads
New
Rear brake pad set for the Toyota Century GZG50, the V12 limousine produced from 1997 to 2017. Supplied by Project A under Toyota part number 04466-40040. The Century is a low-mileage, high-mass vehicle, and that combination produces a specific wear pattern: the friction material often has plenty of life left while the pad backing plates and caliper hardware have corroded from years of standing. On a car like this, condition matters more than measured pad thickness. Fit as an axle set. Strip and clean the caliper carriers properly, replace any corroded shims, and check the discs for surface rust pitting, which on a rarely-used car is more likely to be the problem than wear. Fits GZG50 and GZG50R.
No image available
New Only 2 left
Brake Pads and Shoes
Toyota Town Ace / Noah / Lite Ace Front Brake Pads
New
Front brake pad set covering the Toyota Town Ace, Town Ace Noah, Lite Ace and Previa range. Supplied by Project A under Toyota part number 04465-28340. These are working vans and light people movers with a forward weight bias, so the front axle takes most of the braking load and the pads wear correspondingly fast under commercial use. Loaded running and stop-start delivery work will shorten pad life considerably compared with the same vehicle used privately. Fit as an axle set and inspect the discs while the caliper is off. On higher-mileage vans check the flexible brake hoses at the same time, a perished hose can act as a one-way valve and hold pressure at the caliper, which drags the pad and destroys a new set quickly. Please confirm your chassis code and model year before ordering, as this pad covers several generations.
No image available
New Only 1 left
Brake Pads and Shoes
Toyota Hiace Front Brake Pads (LH / RZH)
New
Front brake pad set for the H100-series Toyota Hiace, covering the LH diesel and RZH petrol chassis codes. Supplied by Project A under Toyota part number 04465-26130. The H100 Hiace is a commercial platform and the front brakes are worked hard, particularly on vehicles that spend their life loaded. Front pads are the fastest-wearing brake component on these by a considerable margin. Fit as an axle set. On a van of this age the caliper hardware deserves as much attention as the pads: check the slide pins for corrosion, the piston dust boots for splits, and the disc faces for scoring. A sticking caliper on an H100 will pull noticeably under braking and will wear one pad to the backing plate while its partner looks nearly new. Fits LH108, LH118, RZH109 and RZH119.
No image available
New
Front Suspension & Bearings
Mitsubishi Delica Space Gear Front Lower Control Arm Bushing
New
Front lower control arm bushing for the Mitsubishi Delica Space Gear, the PD/PE/PF-series four-wheel-drive van built from 1994 to 2007. Genuine Mitsubishi part MR112711. The lower arm bushing is a bonded rubber-and-steel component that locates the control arm to the subframe while allowing it to pivot through suspension travel. As the rubber perishes and separates from its sleeve the arm gains unwanted movement, and the symptoms follow a familiar pattern: a knock over bumps, vague or wandering steering, uneven front tyre wear, and an alignment that will not hold its settings. Space Gears are heavy, frequently used off-road and now all well past twenty years old, so these bushings are a routine replacement rather than an unusual failure. The same part serves both left and right sides. Pressing the old bushing out and the new one in requires a press or a proper bush tool, and a wheel alignment afterwards is not optional.
No image available
New Only 2 left
Engine Oil Filters
Isuzu Elf / Nissan Atlas / Mazda Titan Oil Filter
New
Oil filter covering the Isuzu Elf light truck alongside its Nissan Atlas and Mazda Titan rebadged equivalents. Supplied under Nissan's Pitwork number AY100-NS030. The Elf, Atlas and Titan are the same vehicle wearing three badges, which is why one filter serves all three. On a commercial diesel the oil filter is doing more work than its counterpart on a passenger car: soot loading is heavier, service intervals are often stretched, and a neglected filter going into bypass puts unfiltered oil straight through the bearings. Change the filter with every oil service, without exception. Fill the new filter with clean oil before fitting where orientation allows, lubricate the seal rather than fitting it dry, and tighten by hand to the mark rather than with a wrench. Fits Elf NKR and NKS series, Nissan Atlas and Mazda Titan.
No image available
New Only 1 left
AIR ELEMENT
Isuzu Elf / Nissan Atlas / Mazda Titan Air Filter
New
Air filter element covering the full Isuzu Elf N-series range along with the Nissan Atlas and Mazda Titan rebadges. Pitwork part number AY120-SZ004. Commercial vehicles ingest considerably more dust than passenger cars, and on a turbodiesel a restricted air filter has consequences beyond fuel economy: the engine runs rich, exhaust gas temperature climbs, and the turbo works against a partial vacuum on its intake side. A filter that looks merely dirty can already be costing measurable power. Inspect at every service and replace on condition rather than strictly on mileage. Vehicles working on unsealed roads or construction sites will need this far more often than the schedule suggests. Never wash and refit a paper element, and never run the engine without one fitted. Covers the NHR, NKR, NHS, NPR, NKS, NPS and NQR chassis codes across the 3.1L 4JG2, 4.3L 4HF1, 4.6L 4HG1, 4.8L 4HL1 and 5.0L 4HJ1 engines.
No image available
New Only 2 left
Brake Pads and Shoes
Isuzu Elf / Nissan Atlas / Mazda Titan Rear Brake Shoes
New
Rear brake shoe set for the Isuzu Elf and its Nissan Atlas and Mazda Titan equivalents. Manufactured by Akebono, a Japanese OE brake supplier, under part number NN4042H. Light trucks in this class run rear drum brakes because drums handle sustained loaded braking well and are cheap to service. What they do not tolerate is neglect: the self-adjuster seizes, the return springs fatigue, and the shoes end up either dragging or sitting too far off the drum. A long parking-brake lever travel is usually the first symptom, well before the service brake feels different. Replace shoes as an axle set and inspect the drum bore for scoring and ovality while it is off. Free and grease the adjuster, check the wheel cylinders for weeping behind the dust boots, and set the adjustment correctly on reassembly. Fits Elf NHR series, Nissan Atlas and Mazda Titan.
No image available
New Only 3 left
Brake Pads and Shoes
Toyota Hilux / Hiace / Dyna / Land Cruiser Rear Brake Shoes
New
Genuine Toyota rear brake shoe set, part number 04495-35230, one of the most widely shared rear drum fitments across the Toyota commercial range, covering Hilux, Hilux Surf, Hiace, Dyna and Land Cruiser applications. Rear drums on Toyota commercials are durable but depend on their adjusters working. When the self-adjuster seizes, the shoes stop taking up wear, the pedal gets long, and the parking brake loses its holding ability, which on a loaded vehicle parked on a slope is a genuine safety matter rather than an inconvenience. Fit as an axle set. Measure the drum bore against the maximum diameter cast into the drum, inspect the wheel cylinders for fluid behind the boots, and free off and grease the adjuster before reassembly. Set the adjustment properly and bed the shoes in with a few moderate stops. Hiace fitment covers the KDH and TRH chassis codes.
No image available
New Only 1 left
Brake Pads and Shoes
Toyota Hiace Rear Brake Shoes (KZH / TRH / LH / RZH)
New
Genuine Toyota rear brake shoe set for the H100-series Hiace, covering an unusually wide span of KZH, TRH, LH and RZH chassis codes built between August 1993 and January 2005. This is the standard rear drum shoe for the H100 platform. On vans of this age the shoes themselves are rarely the whole job: the adjusters seize, the hold-down and return springs fatigue, and the wheel cylinders begin to weep behind their dust boots. Any of those will leave the brake either dragging or ineffective regardless of how much friction material is fitted. Replace as an axle set, check the drum bore against its maximum diameter, and inspect the wheel cylinders while the drum is off. Free off and grease the adjuster, set it correctly, and confirm the parking brake holds properly before returning the vehicle to service. Toyota also lists this shoe under part number 04495-26240.