Authentic JDM Parts
Quality OEM and aftermarket parts for your Japanese vehicles. From engines to body parts — we've got you covered.
← Browse by Make / Model instead209+
Parts Available
100%
Quality Guaranteed
Fast
Shipping
New
Brake Components
Honda Step-Wagon Front Brake Rotors (RK)
Front brake rotors for the fourth-generation Honda Step-Wagon, the RK series built from 2009 to 2015. Manufactured by DriveJoy, Tokico's Japanese OE-tier aftermarket brand, under Honda part number 45251-TA0-A01.
The Step-Wagon is a tall, heavy eight-seat MPV and the front discs carry almost all of its braking load. The characteristic complaint on these is a pulsation through the pedal that builds over time, which is disc thickness variation rather than genuine warping, and it is not fixed by fitting new pads alone.
Replace rotors in axle pairs and fit new pads at the same time. Clean the hub face back to bare metal before mounting, as rust trapped between hub and rotor introduces runout from the moment it is bolted up. Torque the wheel nuts properly and evenly, uneven wheel-nut torque is a genuine cause of disc distortion on this platform.
New
Only 1 left
AIR ELEMENT
Toyota Grand Hiace Air Filter
Air filter element for the Toyota Grand Hiace, covering both the VCH petrol V6 and KCH diesel chassis codes from the 1995 to 2002 production run. DriveJoy part under Toyota number 17801-67020.
The Grand Hiace is now a well-established import and parts availability for it is thinner than for the mainstream Hiace, which makes correct routine servicing more worthwhile rather than less. A restricted air filter on the 5VZ-FE petrol V6 shows up as sluggish throttle response and poor economy before it shows up anywhere else.
Inspect at every service and replace on condition. Tap out loose debris to check the element, but never wash a paper filter and refit it, and never run the engine without one in place.
Fits KCH and VCH chassis codes.
New
Only 1 left
Water Pumps
Toyota Grand Hiace / Hilux Surf / Prado Water Pump
Water pump covering the Toyota Grand Hiace along with the Hilux Surf VZN180 and VZH185 and the Land Cruiser Prado VZJ90. DriveJoy part under Toyota number 16100-69405.
The water pump circulates coolant through the block, head and radiator, and it is driven off the timing belt on these engines, which makes it a component worth replacing pre-emptively rather than waiting for it to fail. Pump failure gives warning in a fairly consistent order: a weep from the telltale hole, then a coolant smell, then bearing noise or play at the pulley, then overheating.
Because the pump is behind the timing belt on this engine family, the sensible approach is to replace pump and belt together. Doing the belt alone and returning six months later for the pump means paying the same labour twice.
Always refill with the correct coolant specification and bleed the system properly afterwards.
New
Only 2 left
Brake Components
Mitsubishi Pajero / Montero Front Brake Rotor
Front brake rotor for the Mitsubishi Pajero and Montero, covering the second-generation Pajero built 1992 to 1996 and the first-generation Pajero Sport / Montero Sport built 1997 to 2004. Manufactured by Raybestos.
These are heavy body-on-frame four-wheel-drives, frequently used loaded, towing or off sealed roads, and the front discs take the great majority of the braking effort. Judder under braking on a Pajero of this age is usually disc thickness variation from heat cycling, and is not resolved by new pads alone.
Replace rotors in axle pairs and fit new pads at the same time. Clean the hub face back to bare metal before mounting. On vehicles with free-wheeling hubs, take the opportunity to check the hub bearing preload while everything is apart, play at the bearing will produce runout no new disc can compensate for.
New
Only 1 left
Engine Parts
Mitsubishi Delica / Pajero LH Rocker Cover
Genuine Mitsubishi left-hand rocker cover, part number MD331652, for the 6G72 V6 as fitted to the Delica Space Gear PD6W and the Pajero, Pajero Sport and Montero.
On a V6 each cylinder bank carries its own rocker cover, and this is the left-hand item. The cover seals the top of the cylinder head and keeps oil contained around the valvetrain. The covers themselves usually only need replacing when they have been damaged, warped by overheating, or had their sealing face ruined by a previous repair, more often the leak is the gasket underneath.
If you are chasing an oil leak from the top of the engine, check whether the cover face is flat and undamaged before assuming the cover needs replacing. Always fit a new gasket, clean both sealing faces completely, and tighten the fasteners evenly to the correct torque in sequence, these covers distort easily if overtightened.
Fits Delica PD6W and Pajero V23W, V33V and V45W.
New
Only 2 left
Engine Parts
Toyota Grand Hiace Front Engine Mount
Genuine Toyota front engine mount for the Grand Hiace, part number 12361-62120, covering the VCH10, VCH16, VCH22 and VCH28 chassis codes.
The engine mount is a bonded rubber and steel assembly that carries the weight of the engine while isolating its vibration from the body. As the rubber ages it softens, cracks and eventually separates from its steel, and the symptoms are distinctive: vibration through the floor and steering at idle, a clunk on gear engagement, and a noticeable lurch of the engine when pulling away or backing off.
Mounts are worth inspecting as a set rather than individually. One collapsed mount loads the others beyond what they were designed for, and replacing a single mount on a vehicle where all of them are twenty-plus years old tends to be a short-lived repair.
Support the engine properly before removing the old mount.
New
Only 2 left
Suspension
Toyota Alphard / Estima Rear Axle Bushing
Genuine Toyota rear axle bushing, part number 48725-58010, covering the 10-series Alphard, the ACR30/ACR40 Estima, the Isis and the Previa.
This bushing locates the rear suspension to the body while allowing controlled movement. As the rubber perishes the axle gains unwanted lateral compliance, and the symptoms are the ones owners usually blame on tyres or alignment: a vague, wandering rear end, a clunk over bumps or on turn-in, uneven rear tyre wear, and a rear alignment that will not stay where it is set.
On vehicles of this age and weight these are a routine wear item. Replace them in pairs rather than singly, as a new bushing working against a perished one on the opposite side gives an inconsistent result.
Pressing is required, and a rear wheel alignment afterwards is necessary rather than optional.
New
Only 2 left
Front Suspension & Bearings
Toyota Grand Hiace / Hiace Front Lower Ball Joint
Front lower ball joint, Toyota part number 43330-29305, covering the Grand Hiace KCH16, VCH16 and VCH28 and the Hiace KZH106, KZH116 and KZH126.
The lower ball joint carries the vehicle's weight through the steering knuckle while allowing the wheel to steer and the suspension to move. It is a genuine safety-critical component: a ball joint that separates completely allows the wheel to collapse under the arch, with obvious consequences.
Warning signs are a knock from the front over bumps or on full lock, vibration through the steering, and uneven or feathered front tyre wear. The definitive check is for play with the suspension unloaded and the wheel rocked top to bottom.
Replace in pairs. A press or ball joint separator is required, and a wheel alignment afterwards is necessary. Fit a new split pin to the castellated nut, never reuse the old one.
New
Only 1 left
Engine Parts
Toyota Grand Hiace Engine Mounting Bracket
Genuine Toyota engine mounting bracket, part number 12303-54071, for the Grand Hiace across both the VCH petrol and KCH diesel chassis codes.
This is the steel bracket that carries the rubber mount, not the mount itself. Brackets rarely fail on their own, but they do crack where they have been loaded by a collapsed mount, and they corrode on vehicles that have spent their life on salted or coastal roads. A cracked bracket produces the same symptoms as a failed mount, vibration and engine movement, and replacing the mount alone will not fix it.
Inspect the bracket whenever a mount is replaced. If you are fitting a new mount to a bracket that shows cracking around its fastener holes or heavy corrosion, replace both together.
Support the engine properly before removing the bracket, and torque the fasteners to specification on reassembly.
New
Only 1 left
Suspension
Toyota Grand Hiace / Hiace Front Upper Suspension Arm Set (LH & RH)
Genuine Toyota front upper suspension arm set, part number 48066-29105, supplied as a matched left and right pair. Covers the Grand Hiace VCH and KCH codes and the Hiace KZH106, KZH120, KZH126, RZH109 and RZH119.
On a double-wishbone front end the upper arm sets camber and caster geometry and carries the upper ball joint. Wear appears in two places, the arm's pivot bushings and the ball joint itself, and both produce the same complaints: a knock from the front over bumps, wandering steering, uneven front tyre wear, and an alignment that drifts out of specification.
Supplied as a left and right set, which is how they should be replaced, fitting one new arm against a worn one gives asymmetric geometry and an alignment that cannot be corrected properly.
A full wheel alignment after fitting is required, not optional.
New
Only 3 left
Engine Oil Filters
Toyota Oil Filter (Commercial & Van Range)
Genuine Toyota oil filter, part number 04152-38010, one of the most widely applied filters in the modern Toyota range. Stocked here for the commercial and van platforms we supply: Hiace and Regius Ace, Grand Hiace, Dyna, Coaster, Land Cruiser, Hilux, Town Ace and Century.
This is a cartridge-type filter rather than a spin-on, supplied as the paper element with its sealing rings. The housing stays on the engine and is reused, which means the O-rings supplied with the element must be replaced every time and lightly oiled before assembly. Reusing an old, hardened O-ring is the single most common cause of a leak after an oil change on these engines.
Change the filter with every oil service. The cartridge housing has a specified torque, and overtightening it splits the housing, a genuinely expensive mistake on an engine where the housing is plastic.
Covers all TRH-series Hiace models.
New
Only 1 left
Engine Oil Filters
Honda Accord / Acty / CR-V Oil Filter
Genuine Honda oil filter, part number 15400-RTA-003, covering the Accord, Acty and CR-V.
This is the standard Honda spin-on filter of its generation and one of the most common service items across the range. It carries an internal anti-drainback valve that keeps oil in the filter when the engine is switched off, which is what allows oil pressure to come up quickly on start-up rather than running the bearings dry for the first second or two. Cheap filters often omit or under-specify this valve, which is a good reason to use the genuine part on an engine you intend to keep.
Change with every oil service. Lubricate the seal with clean oil before fitting, never fit it dry, and tighten by hand to the mark on the filter body rather than with a wrench.