Honda STEP-WAGON parts

Fits all STEP-WAGON codes Pick a code
31 parts for the STEP-WAGON
No image available
New Only 1 left
Steering
Outer Tie Rods
New
Outer Tie Rods to fit the Honda Step WGN (RG1), 2000cc petrol. Genuine JDM part imported from Japan by AutoCom JDM Motors, Abbotsford BC. Contact us for current pricing, availability and Canada-wide shipping.
Honda Step-Wagon Rear Power Sliding Door Regulator
New Only 1 left
Electrical
Honda Step-Wagon Rear Power Sliding Door Regulator
New
Genuine Honda rear power sliding door regulator, part number 72710-SLJ-013, for the Step-Wagon RG1 and RG2. The regulator is the motorised mechanism that drives the powered sliding door open and closed. Failure is a common complaint on power-door Hondas of this generation and gives a fairly consistent set of symptoms: the door opens or closes part way and stops, moves slowly or unevenly, makes a grinding or clicking noise from the track area, or stops responding to the remote and switch entirely while still operating by hand. Before ordering, confirm the fault is the regulator rather than something simpler. A worn roller or a dirty, obstructed track will cause the door's safety system to reverse or stop it, and the control unit will refuse to drive a door that is binding mechanically. Cleaning and lubricating the track is worth doing first. Fits RG1 and RG2 only.
Honda Step-Wagon Front Windshield
New Only 3 left
Front Windshields
Honda Step-Wagon Front Windshield
New
Front windshield glass for the Honda Step-Wagon RG1 and RG2, built between 2005 and 2009. Laminated safety glass cut to factory dimensions for a direct glue-in replacement. Laminated construction bonds two layers of glass to an interlayer, so an impact cracks the outer layer without the screen breaking apart. The bonded screen is also structural: it contributes to roof strength in a rollover and provides the backstop that the passenger airbag deploys against, which is why the quality of the bond matters as much as the quality of the glass. This is a bonded installation requiring the correct urethane adhesive and primer, and should be fitted professionally. Allow the adhesive its full safe-drive-away time before the vehicle returns to the road. Fits RG1 and RG2. Please confirm your mirror mount and shade band requirements before ordering.
No image available
New
Brake Pads and Shoes
Honda Step-Wagon / Odyssey Rear Brake Pads
New
Rear brake pad set covering the RG-series Honda Step-Wagon and the RB-series Honda Odyssey, two platforms that share rear brake hardware. Rear pads on these wear slowly, which in practice means they are usually replaced because the caliper has started to stick rather than because the friction material has run out. The rear caliper slides on both platforms are a known corrosion point, and a seized slide holds the pad against the disc, producing heat, smell and rapid one-sided wear. Fit as an axle set. Strip, clean and re-grease the slides, and confirm both pads move freely in the carrier before refitting. If the disc is scored or has a heavy outer lip, replace it, a new pad on a ridged disc will never bed properly. Fits Step-Wagon RG1 to RG4 and Odyssey RB1 to RB4.
No image available
New
Brake Pads and Shoes
Honda Step-Wagon / Odyssey Front Brake Pads
New
Front brake pad set covering the RG-series Honda Step-Wagon and the RB-series Honda Odyssey. The companion front set to part 43022-SFE-N00. The fronts on both platforms do the bulk of the braking and wear accordingly, typically two to three times faster than the rears. Wear is usually even, and the first sign is the wear indicator squealing under light braking. Fit as an axle set and check disc thickness against the minimum stamped on the disc hub while the caliper is off. A pedal pulsation on these is almost always disc runout rather than a pad problem, and fitting new pads to a warped disc will not fix it. Fits Step-Wagon RG1 to RG4 and Odyssey RB1 to RB4.
No image available
New
Brake Components
Honda Step-Wagon Front Brake Rotors (RK)
New
Front brake rotors for the fourth-generation Honda Step-Wagon, the RK series built from 2009 to 2015. Manufactured by DriveJoy, Tokico's Japanese OE-tier aftermarket brand, under Honda part number 45251-TA0-A01. The Step-Wagon is a tall, heavy eight-seat MPV and the front discs carry almost all of its braking load. The characteristic complaint on these is a pulsation through the pedal that builds over time, which is disc thickness variation rather than genuine warping, and it is not fixed by fitting new pads alone. Replace rotors in axle pairs and fit new pads at the same time. Clean the hub face back to bare metal before mounting, as rust trapped between hub and rotor introduces runout from the moment it is bolted up. Torque the wheel nuts properly and evenly, uneven wheel-nut torque is a genuine cause of disc distortion on this platform.
Honda Stepwagon (RK1) Rear Brake Shoe
New Only 2 left
Brake Pads and Shoes
Honda Stepwagon (RK1) Rear Brake Shoe
New
Keep your Honda Stepwagon safely secured with this high-quality Rear Parking Brake Shoe Set, designed specifically for the 4th Generation Honda Stepwagon (RK1–RK7, 2009–2015). The parking brake shoe is a curved piece of friction material that presses against the inside of the brake drum when the handbrake or e-brake is engaged. In vehicles with rear disc brakes like the Stepwagon RK1, parking brake shoes are part of an internal drum brake system, known as a drum-in-hat configuration. The parking brake operates separately from the primary braking system and functions through a series of mechanical linkages or cables; when the driver pulls the handbrake lever, a cable activates the brake mechanism, pulling the parking brake shoes against the inside of the rear rotor's drum-in-hat. The friction created between the brake shoes and the drum prevents the wheels from turning, keeping the vehicle stationary. The brake shoe carries the brake lining, which is riveted or bonded to the shoe. When the brake is applied, the shoe moves and presses the lining against the inside of the drum; the friction between lining and drum provides the braking effort. Over time, these shoes will naturally wear and require replacement. Common causes of failure include excessive wear from frequent use, which causes the friction material to wear down and reduce effectiveness, as well as rust and corrosion from moisture and debris, which can cause the shoes to seize up or stick in place.